Bios Mods -The Best BIOS Update and Modification Source

Full Version: HP MCP61PM-HM (Nettle3) 5.17 With Unlocked Overclocking Options
You're currently viewing a stripped down version of our content. View the full version with proper formatting.
Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
currently reading this 
https://www.bios-mods.com/bios-recovery/...-recovery/
would this be the correct route to get back to stock bios then re do everything but nettle 3 lmao
im such a greenthub but hey im learning how to mess things up...
(02-26-2019, 10:42 AM)cosmothelame Wrote: [ -> ]currently reading this 
https://www.bios-mods.com/bios-recovery/...-recovery/
would this be the correct route to get back to stock bios then re do everything but nettle 3 lmao
im such a greenthub but hey im learning how to mess things up...


you can try...

are you sure your other board has a mountable / plugable eeprom bios chip?

are the chips of the same model, or of the same size?
you could try a hot swap, meaning. you boot the other board, go under FREEDOS, then unplug the bios chip, plug the bricked chip, and then start the DOS command to flash the chip. when done, you switch off, take the bios chip out and try on the nettle 3
(02-26-2019, 10:52 AM)bolc Wrote: [ -> ]
(02-26-2019, 10:42 AM)cosmothelame Wrote: [ -> ]currently reading this 
https://www.bios-mods.com/bios-recovery/...-recovery/
would this be the correct route to get back to stock bios then re do everything but nettle 3 lmao
im such a greenthub but hey im learning how to mess things up...


you can try...

are you sure your other board has a mountable / plugable eeprom bios chip?

are they of the same model? if yes, you could try a hot swap, meaning.
you boot the other board, go under FREEDOS, then unplug the bios chip, plug the bricked chip, and then start the DOS command to flash the chip. when done, you switch off, take the bios chip out and try on the nettle 3

ok so the mcp61pm-hm rev 2.2 is the mobo with bios chip that I put nettle 2 by mistake
I have the other board mcp61pm-hm rev 1.1 and it has no 8 pin chip the boards are slightly different but working and running win 7 ultimte
so if I power up the 1.1 mobo is there a way to connect the 2.2 some how n flash that way lol
ok so could I just re download everything to my laptop then format usb then put old bios on the usb plug it into desktop and power it on would that force it to load so I could see bios? I currently don't have another bios chip or re flashboard.

is there not a way to do this by usb? im stuck at black screen no beeps or sounds.


just need to find a way to re program stock bios via usb? is it possible
Good morning from Argentina! I buy an cheap EEPROM Programmer USB and can flash a 1MB chip from another dead motherboard with the .bin file. Happy to say that it´s working at first try. 30 seconds to program the chip and ready to install S.O. I´m posting from an Athlon II X2 250, Nettle 3. Smile
Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34