Hi
Need help to remove the Whitelist from my Bios file.
https://www.sendspace.com/file/y9ktyy
Is any system changes like new SSD or extra RAM possible after removing the Whitelist?
In advance thanks!
Regards
Mike Thomson
Didn't work. Should I try the USB tool?
Quote:Microsoft Windows [Version 6.3.9600]
© 2013 Microsoft Corporation. All rights reserved.
C:\windows\system32>cd\
C:\>fptw64 -f bios.rom -bios
Intel ® Flash Programming Tool. Version: 9.5.14.1724
Copyright © 2007 - 2013, Intel Corporation. All rights reserved.
Platform: Intel® HM87 Express Chipset
Reading HSFSTS register... Flash Descriptor: Valid
--- Flash Devices Found ---
GD25Q64 ID:0xC84017 Size: 8192KB (65536Kb)
PDR Region does not exist.
GBE Region does not exist.
- Reading Flash [0x800000] 6656KB of 6656KB - 100% complete.
Error 7: Hardware sequencing failed. Make sure that you have access to target fl
ash area!
Trying to erase the same block (iteration: 2)
Error 7: Hardware sequencing failed. Make sure that you have access to target fl
ash area!
Trying to erase the same block (iteration: 3)
Error 7: Hardware sequencing failed. Make sure that you have access to target fl
ash area!
Failed to erase this block 3 times!!
C:\>
Regards Mike
Hi.
Receive an error via USB as well
Will you/I still be able to use the 9ECN40WW(V3.00) version of the BIOS?
Regards Mike
Hello BDMaster,
I own a Lenovo Y70-70 touch. I want to use it as a hackintosh platform, so I needto change the wifi card. I bought a Dell 1560 card with a BCM9435352Z chip.
The card is not on the bios whitelist, so the whitelist must die
I do not need the advanced bios menu, but it wouldn't hurt either to have them, whitelist is a priority.
The laptop currently is at Bios v3.03
In the beginning I did not understand the instructions here correctly, so I downgraded to 1.14 and flashed the bios made for another user: Lenovo_Y50-70_Y70-70_Touch_9ECN31WW_NWL_ADV_sk8rjess. Downgrading first was the only method I could get to work for flashing another bios.
This did erase the whitelist and unlock advanced menus, but my Geforce GTX 960M stopped working. So I went back to the original WLAN card and flashed the original 3.03 again.
I did run bios tool you provided, and added the aida64 report into results.rar. Here it is:
https://www.sendspace.com/file/dhjie8
I will donate for sure
Thanks for your support!
Everything went great! Thank you, donation sent!
Regards
Gregor
Hmm, ok, there is a big issue:
The bios update went well and I can enter the bios. It shows 3.03 bios version and 1.14 for the EC.
If you then save the bios and exit, the "Novo" key for entering the bios stops working one you power off the laptop. I double checked it by reverting to the stock 3.03 bios (Novo key works), then flashing 1.14 and 3.03 modified again, entering bios, not changing any value but saving. Once you turn off, the novo key is dead and you can not enter the bios anymore.
Any idea what to do next?
Regards
Gregor
It's normal this as It's wrote into Instructions that will disalign the Biod and EC !
TO avoid this You need the Tools and You have to get the Full Dump Firmware
reading the Eeprom Chip then i will patch this file and You will rewrite It back
into Eeprom Chip !
This is lonely way to avoid SPI PGM and Clip , look here :
https://www.bios-mods.com/forum/Thread-R...5#pid74575
let me know
Regards
Try to Reset CMOS remoiving battery form MoBo and RAM Mdules , remove Power coed and press switch on
Button for some seconds !
Remount all and try again (Embedded Controller Code is just to use the Keyboard before Bios start) !
(10-18-2015, 06:23 PM)Xerivar Wrote: [ -> ]Hmm, ok, there is a big issue:
The bios update went well and I can enter the bios. It shows 3.03 bios version and 1.14 for the EC.
If you then save the bios and exit, the "Novo" key for entering the bios stops working one you power off the laptop. I double checked it by reverting to the stock 3.03 bios (Novo key works), then flashing 1.14 and 3.03 modified again, entering bios, not changing any value but saving. Once you turn off, the novo key is dead and you can not enter the bios anymore.
Any idea what to do next?
Regards
Gregor
Try this Recovery Bios Procesure :
8821
1, copy ZIVY2.bin files to the U packing list and ensure no suffix in the directory name to bin the relevant documents (U disk formatted as fat or FAT32, no guide information)
2, shut down and unplug the battery, power adapter
3, insert U disk
4, do not put down the FN+R hotkey
5, insert power adapter
6, starting
7, the release of FN+R hotkey
8, the system automatically, until the end of the sound, the system will automatically restart and normal boot (this process must not be cut off!)
download link
http://rghost.net/6qpB8FWCS
Let me know
Regards