(11-14-2019, 01:47 PM)Stealth2019 Wrote: [ -> ]I attached the CPU-Z report in TXT format
As I thought
R7LD224.BIN is modded
R7LD223.BIN with date 02/23/10.
(11-14-2019, 01:47 PM)Stealth2019 Wrote: [ -> ]Should i write the F8N Bios like that, or should I extract ncpucode.bin, agesacpu.rom from it and insert them into my original bios ?
Use hardware programmer to test. I think inserting (only) ncpucode.bin & agesacpu.rom will not help.
OK...i will do that in a couple of minutes.
With the F8N bios from the gigabyte board is even worse. When i press the power button the pc starts and after a second it powers off... seems like a protection or something. I can power it back on only if I switch off the power supply then switch back on.
What is about
F8I? I wrote:
(11-14-2019, 01:09 PM)DeathBringer Wrote: [ -> ]And you can try F8I BIOS from Gigabyte GA-MA790FX-DS5. Note that you need to double firmware file to make correct size.
BTW: What's version of
CBROM you use for modding this BIOS?
(11-14-2019, 02:40 PM)DeathBringer Wrote: [ -> ]What is about F8I? I wrote:
(11-14-2019, 01:09 PM)DeathBringer Wrote: [ -> ]And you can try F8I BIOS from Gigabyte GA-MA790FX-DS5. Note that you need to double firmware file to make correct size.
BTW: What's version of CBROM you use for modding this BIOS?
I use cbrom version 1.95. I saw that version 1.96 crashed when i tried to extract the ncpucode.bin
I will try F8I right now.
Will this dos command be enough to concatenate the same file to make it double?
copy /b bios.f8i+bios.f8i bios.bin
Or should i use a hex editor to do it ?
(11-14-2019, 02:54 PM)Stealth2019 Wrote: [ -> ]I use cbrom version 1.95. I saw that version 1.96 crashed when i tried to extract the ncpucode.bin
How you update AGESACPU.ROM by this version of CBROM?
(11-14-2019, 02:54 PM)Stealth2019 Wrote: [ -> ]copy /b bios.f8i+bios.f8i bios.bin
It's enough for test.
In order to update the AGESACPU.ROM I took a screenshot before i have extracted and released all the modules inside my original bios until the ncpucode.bin. When all modules are extracted and released my bios contained only ncpucode.bin, hole0 and hole1 components.
Then I put the modules back in the order they were in the original bios and instead of my original AGESACPU.ROM I insert the AGESAPU.ROM file i have extracted from another bios. The screenshot i took helps me to know the exact order.
Is it ok this method or am i doing something wrong?
Try to clean all the modules in BIOS for 790FXB-M3H5 and insert modules from original BIOS. Then flash it.
(11-14-2019, 03:29 PM)DeathBringer Wrote: [ -> ]Try to clean all the modules in BIOS for 790FXB-M3H5 and insert modules from original BIOS. Then flash it.
I tried with the doubled F8I bios...it didn't post but at least it didn't power off by itself.
Will try to clean the 790FXB-M3H5 bios
Should i insert all modules from my original bios including my original AGESACPU.ROM and NCPUCODE.BIN?
(11-14-2019, 03:47 PM)Stealth2019 Wrote: [ -> ]Should i insert all modules from my original bios including my original AGESACPU.ROM and NCPUCODE.BIN?
Yes, all of them including main module
d7ld706.BIN.