I need updated Marvell 9123 firmware to:
ASUS Rampage III Formula BIOS 0903
Unfortunately there is no way to keep the bios from re-flashing the firmware when I update it manually. I found no option in the BIOS.
If you would like to also update the Intel RAID firmware and LAN, that would be nice but not required.
I have attached both the 0903 BIOS and the Marvell 9123 firmware. I was not sure what exactly you needed from the Station-Drivers site so I included everything that comes when you download their firmware package.
I just joined today and found this site to be an excellent resource.
I will happily donate! : )
[
attachment=2865]
[
attachment=2866]
Ditto, I would also like to have this bios.
Same Request - I'm running an ASUS RAMPAGE III FORMULA with a Corsair GT 120 Solid State Drive and I'm running into stability issues using the marvell sata 6 controller. The intel sata 3 works fine but my solid state was meant to run on sata 6. The solidstate is running off the latest corsair firmware etc. So I'd like to take a crack at having the firmware updated for the marvell controllers, I noticed mine are running at 1.0.0.xxxx while the latest marvell firmware is going at 2.2.0.1125
I’d appreciate anyone that could help, please. Otherwise I'm SOL since the motherboard seems to even downgrade the sata firmware of other marvell controller cards. $30 down the tube.
Latest Rampage III Formula Bios 0903
http://support.asus.com/download.aspx?SL...zsToHRsCro
Latest Marvell MV-91xxx Firmware 2.2.0.1125 - 05/01/12
http://www.station-drivers.com/telecharg...s.com).zip
OROMS Updated:
Intel RAID ROM 10.5.0.1034 -> 11.0.0.1339
Marvell OROM 1.0.0.1019 -> 1.0.0.1029
JMicron 1.07.14 -> 1.07.28
ASUS SLIC 2.1 Added
ASUS_Rampage_III_Formula_0903_OROMS_ASUS_SLIC_2.1_SSV3.rar
http://www.sendspace.com/file/ggjgu7
(02-04-2012, 06:30 PM)DMAN999 Wrote: [ -> ]OROMS Updated:
Intel RAID ROM 10.5.0.1034 -> 11.0.0.1339
Marvell OROM 1.0.0.1019 -> 1.0.0.1029
JMicron 1.07.14 -> 1.07.28
ASUS SLIC 2.1 Added
ASUS_Rampage_III_Formula_0903_OROMS_ASUS_SLIC_2.1_SSV3.rar
http://www.sendspace.com/file/ggjgu7
Thank you very much! Very fast too I'm shocked. I'll start updating my bios right away, thanks again!
(02-04-2012, 06:30 PM)DMAN999 Wrote: [ -> ]OROMS Updated:
Intel RAID ROM 10.5.0.1034 -> 11.0.0.1339
Marvell OROM 1.0.0.1019 -> 1.0.0.1029
JMicron 1.07.14 -> 1.07.28
ASUS SLIC 2.1 Added
ASUS_Rampage_III_Formula_0903_OROMS_ASUS_SLIC_2.1_SSV3.rar
http://www.sendspace.com/file/ggjgu7
OH THANK YOU!!!
I had nearly forgotten about requesting this. I'm really happy to see an update! Thank you so much!
I will test it out tomorrow sometime. I'm busy this evening. I will post an update to let you all know how it worked out.
Thanks again!!!
Also thanks vxarctic for scouring the forums and bringing my thread back from the dead, lol.
Is this using the 9128 marvell controller rom update I hope so as the Rampage 3 Formula has the 9128 not the 9123.
thanks for any replys reguarding this i am hoping that this may fix issues i am having here.
(02-04-2012, 09:21 PM)sphroth Wrote: [ -> ] (02-04-2012, 06:30 PM)DMAN999 Wrote: [ -> ]OROMS Updated:
Intel RAID ROM 10.5.0.1034 -> 11.0.0.1339
Marvell OROM 1.0.0.1019 -> 1.0.0.1029
JMicron 1.07.14 -> 1.07.28
ASUS SLIC 2.1 Added
ASUS_Rampage_III_Formula_0903_OROMS_ASUS_SLIC_2.1_SSV3.rar
http://www.sendspace.com/file/ggjgu7
OH THANK YOU!!!
I had nearly forgotten about requesting this. I'm really happy to see an update! Thank you so much!
I will test it out tomorrow sometime. I'm busy this evening. I will post an update to let you all know how it worked out.
Thanks again!!! Also thanks vxarctic for scouring the forums and bringing my thread back from the dead, lol.
That OROM is for both Marvell 9123 and 9128.
Tested the mod out over the weekend!
After running ATTO's Hard drive bench mark a couple times, it seems I lost a tiny bit of speed on my read/writes. A couple megs, it is no big deal.
I will have to reformat and install updated Marvell drivers to see if I can squeeze any more speed out of the controller. Right now I think I am using whatever Microsoft has for AHCI drivers.
Also I noticed that if I try to upgrade the 9123/9128 firmware to 2.2.0.1125, the BIOS will re-flash it. I am not entirely sure how to get around this. If anyone knows how I can get around this I would be ecstatic!
Other then that, the mod is stable and I am very happy with my BIOS Mod. Thanks DMAN!
Formatted my machine and installed Windows 7 Pro x64.
Using the latest Marvell driver with the new BIOS, after the format, I managed to achieve a little bit better performance then I used too. Again, only a couple of megs of difference. I believe this is the highest performance I have gotten with my SSD on the Marvell controller.