-Manufacturer: Phoenix Technologies Ltd.
-Motherboard Model: Sony VGN-SZ1XP_C
-Bios revision: is this the bios version? if yes: BIOS Version R0083N0
-Bios Type: Phoenix BIOS
-Bios Download Link:
http://support.vaio.sony.eu/computing/va...px?l=en_GB&url=Downloads/PH/B/SYS/PHBSYS-01041222-UN.exe&m=VGN-SZ1XP_C&ip=PHBSYS-01041222-UN.htm
-RW Everything Report Download Link:
Have run RW everything but no slic tab appears.
Any assistance greatly appreciated.
Here you go , i used Sony 2.1 SLIC + Certificate Included:-
1. Copy and paste ******.XRM-MS certificate file into C-Drive.
2. After pasting this file into C-Drive, go to START - ALL PROGRAMS - ACCESSORIES - COMMAND PROMPT. Right click on Command Prompt and RUN AS ADMINISTRATOR.
3. When Command Prompt opens, type at the prompt: slmgr.vbs -ilc c:\********.xrm-ms and hit the Enter Button. Wait for the Script Host to answer you with a message that the license was installed successfully....this could take a few minutes and so be patient.
4. After receiving the message that the license was installed successfully, type at the command prompt:
slmgr.vbs -ipk *****-*****-*****-*****-***** (Replace with any OEM SLP Product Key for your installed version of Windows 7 , they are not hard to find).Be Patient and wait for the message to say that the Product Key was sucessfully installed. After it says successfully installed, reboot the computer.
5. When you are back at your desktop, go to START - COMPUTER - right click on Computer and choose PROPERTIES and see if it is activated with an OEM product ID.
http://dl.dropbox.com/u/747181/Sony%20Va...34s282.zip
Flash at your own risk!
Please Report Back With Whether It Worked Or Not!
Please Consider A Small Donation As A "Thank You" If You Are Happy With Our Work
Regards
Admin
(02-26-2010, 07:44 PM)1234s282 Wrote: [ -> ]Here you go , i used Sony 2.1 SLIC + Certificate Included:-
1. Copy and paste ******.XRM-MS certificate file into C-Drive.
2. After pasting this file into C-Drive, go to START - ALL PROGRAMS - ACCESSORIES - COMMAND PROMPT. Right click on Command Prompt and RUN AS ADMINISTRATOR.
3. When Command Prompt opens, type at the prompt: slmgr.vbs -ilc c:\********.xrm-ms and hit the Enter Button. Wait for the Script Host to answer you with a message that the license was installed successfully....this could take a few minutes and so be patient.
4. After receiving the message that the license was installed successfully, type at the command prompt:
slmgr.vbs -ipk *****-*****-*****-*****-***** (Replace with any OEM SLP Product Key for your installed version of Windows 7 , they are not hard to find).Be Patient and wait for the message to say that the Product Key was sucessfully installed. After it says successfully installed, reboot the computer.
5. When you are back at your desktop, go to START - COMPUTER - right click on Computer and choose PROPERTIES and see if it is activated with an OEM product ID.
http://dl.dropbox.com/u/747181/Sony%20Va...34s282.zip
Flash at your own risk!
Please Report Back With Whether It Worked Or Not!
Please Consider A Small Donation As A "Thank You" If You Are Happy With Our Work
Regards
Admin
Hi Admin thanks for the quick response, really appreciated. I have just tried to run the flashbios and get the following error:
Bios update failed. Image file is either not valid or damaged
Bios image verification failed
Error code -149
Not sure what to try now, so any further help greatly appreciated.
Regards
Ne0dev
Google instructions for bootable DOS disk
Place .WPH file and phlash16.exe on the bootable DOS disk , boot from it and type the following at the DOS prompt
phlash16.exe R0083N0.WPH
good Luck!
Admin
(02-27-2010, 10:12 PM)1234s282 Wrote: [ -> ]Google instructions for bootable DOS disk
Place .WPH file and phlash16.exe on the bootable DOS disk , boot from it and type the following at the DOS prompt
phlash16.exe R0083N0.WPH
good Luck!
Admin
Right,
I have created a bootable usb drive and downloaded the phlash16 utility. I put both files on the usb key and booted into dos. ran the phlash utility with the wph file but the following error:
Phoenix Phlash16 error
file open failed on R0083N0
Press any key to exit.
Not sure wot else to try now, so grateful for more suggestions.
Thanks
Ne0dev
just to confirm you did type R0083N0.WPH didnt you?
Not R0083N0?
Admin
(03-01-2010, 05:54 PM)1234s282 Wrote: [ -> ]just to confirm you did type R0083N0.WPH didnt you?
Not R0083N0?
Admin
Hi Admin,
No I didn't, but have since re tried with correct syntax andnow get the following error in the phlash16 program:
Phoenix Phlash16 Error
Platform Signature Not found in the Interface
Press any key to reboot
Not sure where to ge from here
Regards
Ne0Dev
Hi Admin
Sorry for the delayed response in continuing this thread.
I havenow had chance to try the second mod you posted and I now get the following error message:
"Platform signature not found in the interface"
Any further suggestions most welcome
Thanks
Ne0dev
1234s282 is still away, but will be back hopefully by the end of the week, so I will forward him this request
TheWiz
Corrupted File