Forum RSS Feed Follow @ Twitter Follow On Facebook

Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[-]
Welcome
You have to register before you can post on our site.

Username:


Password:





[-]
Latest Threads
FX-4130 support on GA-880GM-UD2H (r1.4)
Last Post: oqx
Today 08:34 AM
» Replies: 3
» Views: 510
Toshiba Satellite L775 BIOS Unlock Reque...
Last Post: R4nd0m1985
Today 03:07 AM
» Replies: 7
» Views: 3083
Acer Aspire M3641
Last Post: gnappolone
Yesterday 01:35 PM
» Replies: 0
» Views: 123
HP 15-ec1037 & AX211
Last Post: DjFapben
Yesterday 10:59 AM
» Replies: 0
» Views: 99
[REQUEST] Lenovo Thinkpad Edge E430 & E5...
Last Post: oplok71
03-25-2025 05:57 PM
» Replies: 495
» Views: 190362
Sony VGN-FE660G R0174J3 With Sony 2.1 SL...
Last Post: goka
03-25-2025 02:29 PM
» Replies: 15
» Views: 18131
W6Li+Pentium II Overdrive
Last Post: VintageHunter
03-24-2025 02:39 PM
» Replies: 41
» Views: 12844
[REQUEST] ACER Aspire A7 715-43G Bios Un...
Last Post: FurknTsc
03-24-2025 11:48 AM
» Replies: 4
» Views: 474
[REQUEST] Panasonic CF-19 MK4 Custom BIO...
Last Post: CF19ByteBuster
03-24-2025 11:10 AM
» Replies: 0
» Views: 215
[REQUEST] Lenovo G400S (7BCNxxWW) Whitel...
Last Post: Dudu2002
03-24-2025 03:45 AM
» Replies: 208
» Views: 95347
[REQUEST] Lenovo G500 (78CNxxWW) Whiteli...
Last Post: Mcfly3770
03-24-2025 03:02 AM
» Replies: 1222
» Views: 397747
Samsung R60: problems with new CPU
Last Post: DeathBringer
03-23-2025 04:52 AM
» Replies: 1
» Views: 224
[REQUEST] HP 22-b016 BIOS Mod for an IDE...
Last Post: CyberTails
03-22-2025 07:26 PM
» Replies: 0
» Views: 283
Packard Bell TE11HC: HM70 mod to accept ...
Last Post: DelusheN
03-22-2025 05:58 PM
» Replies: 6
» Views: 1535
Acer Aspire 7740G: Upgrading from i3-330...
Last Post: DeathBringer
03-22-2025 01:27 AM
» Replies: 13
» Views: 620
[Paid Request] Adding Epyc 2nd gen CPU s...
Last Post: TikerLynx
03-21-2025 03:01 PM
» Replies: 0
» Views: 409
[REQUEST] Lenovo Ideapad 100-14IBD & 100...
Last Post: dota1990
03-21-2025 06:04 AM
» Replies: 23
» Views: 11858
[REQUEST] Lenovo G510 (79CNxxWW) Whiteli...
Last Post: Dudu2002
03-21-2025 05:05 AM
» Replies: 595
» Views: 266687
[Request] HP Prodesk 600 G3 (DM) Mini/Mi...
Last Post: DeathBringer
03-19-2025 02:45 PM
» Replies: 1
» Views: 512
Lenovo Z580 BIOS Mod V3.1 FINAL [02/07] ...
Last Post: kocyigityunus
03-19-2025 11:01 AM
» Replies: 253
» Views: 279005

[REQUEST] Acer VN7-792G BIOS Unlock
#11
(09-13-2016, 04:26 PM)Dudu2002 Wrote: Hi
ONLY SPI programmer+SOIC8 clips

What u mean with that? I dont understand u?
find
quote
#12
Hello Vodek.
Will your method work on a vn7-792g laptop. I would like to use win 7 on this machine
but have no audio available, which may be accessible from the advance menu.
Also to choose which graphics is default.
I have the latest BIOS v1.09 installed.
Is this possible,
Many thanks.
find
quote
#13
(11-13-2016, 05:59 AM)Saddle Wrote: Will your method work on a vn7-792g laptop. I would like to use win 7 on this machine
but have no audio available, which may be accessible from the advance menu.
Also to choose which graphics is default.
NO
Bios mod can be flashed using SPI-programmer+SOIC8 clip only
find
quote
#14
(11-13-2016, 06:23 AM)Dudu2002 Wrote:
(11-13-2016, 05:59 AM)Saddle Wrote: Will your method work on a vn7-792g laptop. I would like to use win 7 on this machine
but have no audio available, which may be accessible from the advance menu.
Also to choose which graphics is default.
NO
Bios mod can be flashed using SPI-programmer+SOIC8 clip only

Thanks for your reply.
What would the procedure be for this, please ?
find
quote
#15
(11-13-2016, 01:37 PM)Saddle Wrote:
(11-13-2016, 06:23 AM)Dudu2002 Wrote:
(11-13-2016, 05:59 AM)Saddle Wrote: Will your method work on a vn7-792g laptop. I would like to use win 7 on this machine
but have no audio available, which may be accessible from the advance menu.
Also to choose which graphics is default.
NO
Bios mod can be flashed using SPI-programmer+SOIC8 clip only

Thanks for your reply.
What would the procedure be for this, please ?

In-short, you use a programmer (can be a USB programmer connected to another computer or the GPIO pins on a Raspberry Pi) and flash a custom BIOS directly to the BIOS chip on the laptop. The programmer is connected to the BIOS chip via a SOIC clip.

Here's a (pretty unexplained) video of the process: https://youtu.be/W8hhMLZwghs (shows the opening of the laptop, attaching the SOIC clip, the long flash writing process (a few mins), and then the end shows the Terminal window for the commands and a close-up of the wires and SOIC clip)

I've done this on a VN7-572G with a Raspberry Pi and Pomona 5250 SOIC clip. Assuming the BIOS chip on the VN7-791G has the same (MX25L6405D) or similar BIOS chip, the same SOIC clip should work.

As for the programmer, a Raspberry Pi and flashrom worked fine for the MX25L6405D my 572G had. To figure out what chip your laptop has, you'll have to look at the model number on the chip itself (rip the keyboard off, look for a small 8-pin chip; there might be 3 of them; on a 572G the chip was towards the middle near the fan). If you're using a RPi, you'll need to manually compile Flashrom if you're using Raspbian.

As for pin layout and what wires go where between the chip and programmer, I had to look at some guide for another chip, and then compare it to the data sheet for my chip (it happened to match).

[Image: 820LcDeSURqbEMgv.jpg]
find
quote
#16
(11-13-2016, 08:39 PM)espionage724 Wrote:
(11-13-2016, 01:37 PM)Saddle Wrote:
(11-13-2016, 06:23 AM)Dudu2002 Wrote:
(11-13-2016, 05:59 AM)Saddle Wrote: Will your method work on a vn7-792g laptop. I would like to use win 7 on this machine
but have no audio available, which may be accessible from the advance menu.
Also to choose which graphics is default.
NO
Bios mod can be flashed using SPI-programmer+SOIC8 clip only

Thanks for your reply.
What would the procedure be for this, please ?

In-short, you use a programmer (can be a USB programmer connected to another computer or the GPIO pins on a Raspberry Pi) and flash a custom BIOS directly to the BIOS chip on the laptop. The programmer is connected to the BIOS chip via a SOIC clip.

Here's a (pretty unexplained) video of the process: https://youtu.be/W8hhMLZwghs (shows the opening of the laptop, attaching the SOIC clip, the long flash writing process (a few mins), and then the end shows the Terminal window for the commands and a close-up of the wires and SOIC clip)

I've done this on a VN7-572G with a Raspberry Pi and Pomona 5250 SOIC clip. Assuming the BIOS chip on the VN7-791G has the same (MX25L6405D) or similar BIOS chip, the same SOIC clip should work.

As for the programmer, a Raspberry Pi and flashrom worked fine for the MX25L6405D my 572G had. To figure out what chip your laptop has, you'll have to look at the model number on the chip itself (rip the keyboard off, look for a small 8-pin chip; there might be 3 of them; on a 572G the chip was towards the middle near the fan). If you're using a RPi, you'll need to manually compile Flashrom if you're using Raspbian.

As for pin layout and what wires go where between the chip and programmer, I had to look at some guide for another chip, and then compare it to the data sheet for my chip (it happened to match).
Thanks for that, he doesn't say much !!!
I think I'll use a SB audio stick for now.

One thing I've noticed using the Intel system Utility is that disabling SECURE BOOT switches
the BIOS to legacy mode, even if UEFI is selected. I scanned with and without SECURE BOOT to
confirm this. I guess that's why I couldn't boot with a UEFI USB to install the OS.
This might be useful for someome.

Thanks for your help.
find
quote
#17
[attachment=11429]
(11-13-2016, 08:39 PM)espionage724 Wrote:
(11-13-2016, 01:37 PM)Saddle Wrote:
(11-13-2016, 06:23 AM)Dudu2002 Wrote:
(11-13-2016, 05:59 AM)Saddle Wrote: Will your method work on a vn7-792g laptop. I would like to use win 7 on this machine
but have no audio available, which may be accessible from the advance menu.
Also to choose which graphics is default.
NO
Bios mod can be flashed using SPI-programmer+SOIC8 clip only

Thanks for your reply.
What would the procedure be for this, please ?

In-short, you use a programmer (can be a USB programmer connected to another computer or the GPIO pins on a Raspberry Pi) and flash a custom BIOS directly to the BIOS chip on the laptop. The programmer is connected to the BIOS chip via a SOIC clip.

Here's a (pretty unexplained) video of the process: https://youtu.be/W8hhMLZwghs (shows the opening of the laptop, attaching the SOIC clip, the long flash writing process (a few mins), and then the end shows the Terminal window for the commands and a close-up of the wires and SOIC clip)

I've done this on a VN7-572G with a Raspberry Pi and Pomona 5250 SOIC clip. Assuming the BIOS chip on the VN7-791G has the same (MX25L6405D) or similar BIOS chip, the same SOIC clip should work.

As for the programmer, a Raspberry Pi and flashrom worked fine for the MX25L6405D my 572G had. To figure out what chip your laptop has, you'll have to look at the model number on the chip itself (rip the keyboard off, look for a small 8-pin chip; there might be 3 of them; on a 572G the chip was towards the middle near the fan). If you're using a RPi, you'll need to manually compile Flashrom if you're using Raspbian.

As for pin layout and what wires go where between the chip and programmer, I had to look at some guide for another chip, and then compare it to the data sheet for my chip (it happened to match).

I notice that the problem seems to be with the VN7-**2G series notebooks, so I had a look at
the difference between the **2G and the **1G (which works).
I found that in the **2G series, there are 3 instances of 0x258, but on the **1G there is only 1.
That being the case, the Efishell command would never work on the**2G series as it will
try and alter the first instance and fail.
If there is a command to address only the second instance, then it may work without the
need for hardware. I attach the text files of the 3 laptops in the thread.
Many Thanks again.


Attached Files
.txt   591G.txt (Size: 379 bytes / Downloads: 37)
.txt   792G.txt (Size: 603 bytes / Downloads: 30)
find
quote
#18
Thumbs Up 
The model is the Acer Aspire V Nitro VN7-792G, here's the link to the Bios file:

https://global-download.acer.com/GDFiles...09_A_A.zip

Attached is a screenshot of the currently available Bios options.

I'm aware that I'll need to use a clip and flasher to make this happen and willing to try it with a modified Bios.

Thanks in advance
find
quote
#19
Good Day.

I have an Aspire VN7-792G-78G4 Nitro black edition with intel i7-6700HQ and Nvidia gtx 960m, Currently running latest bios version 1.09 from Acer website, I would like to unlock advanced menu on this laptop bios,

I would really appreciate if someone can do that for me, link to original bios is

https://global-download.acer.com/GDFiles...ER&SC=PA_6



Thanks in advance and please let me know if it is possible to unlock it without bricking the laptop.

Best Regards.

Frank
find
quote
#20
(08-12-2017, 06:17 AM)FrankmNLD Wrote: Good Day.

I have an Aspire VN7-792G-78G4 Nitro black edition with intel i7-6700HQ and Nvidia gtx 960m, Currently running latest bios version 1.09 from Acer website, I would like to unlock advanced menu on this laptop bios,

I would really appreciate if someone can do that for me, link to original bios is

https://global-download.acer.com/GDFiles...ER&SC=PA_6



Thanks in advance and please let me know if it is possible to unlock it without bricking the laptop.

Best Regards.

Frank
Hi
Your bios chip is rewrite protected
Bios mod can be flashed using SPI-programmer+SOIC8 clip only
find
quote


Forum Jump:


Users browsing this thread: 3 Guest(s)