[REQUEST] Lenovo Thinkpad Edge E135 (HMETxxWW) Whitelist Removal

[shanny]

Hmm, maybe the Card is incompatible with my lenovo. Same Problem with WLAN.

w/o Pin20 and with Pin20 same behaviour

[BDMaster]

Hmm, maybe the Card is incompatible with my lenovo. Same Problem with WLAN.

w/o Pin20 and with Pin20 same behaviour

I want to know if now You got some error 1802 as this Mod is different yet than before and different than post #58.
May be You're right as I have done many Bios Mod on E135 and all working !
Look here e.g. :

https://www.bios-mods.com/forum/Thread-R...st-removal

So the Best Mod is that at post #58 but WLan is not working.
There is some Code that disable power on Wireless Card, but I don't know where is.
I will try the last Bios Mod based on post #58 with some others differences and I will upload here quickly.
So You will try this one too and hoping It could be work.
Let me know
Regards

[shanny]

Thank you. No, I do not get errors at startup.
If this Bios is not working, my WLAN Card has to be the problem. But again, really really thank you for your hard work!

[BDMaster]

Thank you. No, I do not get errors at startup.
If this Bios is not working, my WLAN Card has to be the problem. But again, really really thank you for your hard work!

So this one is equal to that post #58 or different ?
If different why ?
I will post the last Bios Mod based on post #58 Bios Mod
quickly.
Meanwhile that one last I posted is similar to the tradictional
Bios Mod, that's why I will know the differences.
Regards

[shanny]

I did not tried Bios from Post #28.
My Notebook is booting normally with Bios from Post #58, #69 and#71. Only Problem is the WLAN connectivity.

[BDMaster]

I did not tried Bios from Post #28.
My Notebook is booting normally with Bios from Post #58, #69 and#71. Only Problem is the WLAN connectivity.

It means that We have bypassed the Whitelist check, but there is something
on powering card that is not working standard.
If I will know what is the issue I will post the solution for You nad for others users
whose use this PCI-Card.
Many thanks for your contribution.
Regards

[shanny]

OK =) We will see, I am here and will waiting.

[Marissa]

I flashed my laptop with the 2.53 BIOS as provided in this thread, the WLAN works in Linux but I have problems with suspend. I can't flash the 2.07 BIOS, pflash hangs in the "read bios file and local bios" screen, before anything happens. What should I do?

EDIT: I got it working thanks to BDMaster <3

[BDMaster]

OK =) We will see, I am here and will waiting.

Ok friend,
I found these informations :

http://www.thinkwiki.org/wiki/Problem_wi...twork_card

I known this and I said about pin 20 and 51 then there is a little chance using a smart solution on Pin 13, but before You have to use a voltmeter to misure etc.

Look here :

"The solution is to connect the ground (GND) to the pin 13. However, since the new RF Silent input signal is active low, grounding the card side will tell it to turn itself off. Therefore, we have to separate pin 13 of the card from the system board and connect ground to the system board side only.

There are many ways to accomplish this. One which doesn't require any soldering is to mask pin 13 on the card with a cellophane tape and use about 3cm of thin wire to connect pin 13 of the connector to the ground. Place one end of the wire on the masked pad and insert the card into the slot. Check if the wire is centered on the pad and try pulling it (but not too hard) to see if it holds. If it comes out easily, pull the card out and repeat. If you successfully attach it, you have to connect the other end to the ground. The best place is the left MiniPCI latch arm. Bend it outside and insert the wire into the small gap between the two pieces of metal the arm is made from. Finally, make sure that the wire doesn't touch anything else and doesn't stand out too much, it must not touch the touchpad electronics when you put the palmrest back on. If in doubt, cover the wire with some insulator. "

If do You want to try You can . . .
Let me know
Regards

[shanny]

Thank you, I recieved a new WLAN Card with Broadcom Chipset and AC Standard. Now it works =)

My intel Card is now inside my server. So it is ok.

Thanks you again =)