Request Foxconn H67S/H61SP Bios ver. A41F1020

[grandtiger]

Foxconn RM3-H2
Motherboard: H67S/H61SP
Bios ver: A41F1020
Bios link: http://www.foxconnchannel.com/driverdown...1F1020.zip

RW everything report attached (need to unzip).

Could you please help add any OEM SLIC2.1?

Thank you very much!

[sovem]

Foxconn RM3-H2
Motherboard: H67S/H61SP
Bios ver: A41F1020
Bios link: http://www.foxconnchannel.com/driverdown...1F1020.zip

RW everything report attached (need to unzip).

Could you please help add any OEM SLIC2.1?

Thank you very much!

Slic: ASUS 2.1
Bios mod: Foxconn_RM3-H2_H67S_H61SP_A41F1020_ASUS21
https://www.box.com/s/k6b51qds4bq9oeturvgx
Update from windows with included flash utility. Run FLASH.bat as administrator. Restart and check slic.
Please post results.

[grandtiger]

Slic: ASUS 2.1
Bios mod: Foxconn_RM3-H2_H67S_H61SP_A41F1020_ASUS21
https://www.box.com/s/k6b51qds4bq9oeturvgx
Update from windows with included flash utility. Run FLASH.bat as administrator. Restart and check slic.
Please post results.

Hi sovem,

Thank you so much for your help!

Unfortunately, I just found that I got the wrong version of BIOS. The version number from my bios setup actually shows A41F1026. However, this version of firmware can not be found on Foxconn's website. Under RM3-H3 bios page, only one version (A41F1P03) is available:
http://www.foxconnchannel.com/ProductDet...T=Barebone&U=en-us0000104#

Under H67S bios page, quite a few versions are available, including the version number I posted originally (A41F1020). However, it doesn't have the version current show in my bios.
http://www.foxconnchannel.com/ProductDet...otherboard&U=en-us0000515

Now I am a bit hesitant to flash this bios mod. Is it safe to flash a different version of bios? I am a newbie in this. What would be your suggestion?

Shall I flash my bios to A41F1P03, re-run and post RW everything report? This version is on both H67S and RM3-H2 pages, and I've checked the binary files, they are idential.

I just downloaded FOX LiveUpdate tool and backed up the current version (A41F1026) of bios, as attached in the post. Is it safer to redo the mod on this one?

Thank you again for you help and any advice you may provide!

[DMAN999]

Module Method Mod:
Foxconn_H67S_A41F1026_HP_SLIC_2.1_Module.rar
http://www.sendspace.com/file/8q4wz0

If the Module Mod doesn't work properly try this SSV2 Mod:
Foxconn_H67S_A41F1026_HP_SLIC_2.1_SSV2.rar
http://www.sendspace.com/file/q3g396

[grandtiger]

Module Method Mod:
Foxconn_H67S_A41F1026_HP_SLIC_2.1_Module.rar
http://www.sendspace.com/file/8q4wz0

If the Module Mod doesn't work properly try this SSV2 Mod:
Foxconn_H67S_A41F1026_HP_SLIC_2.1_SSV2.rar
http://www.sendspace.com/file/q3g396

Thanks a lot for your help! I made sure the jumper is set correctly and tried both of your mods, but got the same error:

PDR Region does not exist.

Error 25: The host CPU does not have write access to the target flash area. To enable write access for this operation you must modify the descriptor settings to give host access to this region.

Any suggestions on what else I could try to proceed?

Thanks again!

[DMAN999]

You need to move the Correct Jumper on that MB to the approprate Position to be able to Flash that BIOS.
Another user had the Exact same error:

for some reason i got an error:

"PDR region does not exist
error 25: the host cpu does not have write access to the target flash area. To enable write access for this operation you must modify the decriptor settingsto give host access to this region."

edit: found the bios lock jumper, and now able to flash the bios

[grandtiger]

You need to move the Correct Jumper on that MB to the approprate Position to be able to Flash that BIOS.
Another user had the Exact same error:

for some reason i got an error:

"PDR region does not exist
error 25: the host cpu does not have write access to the target flash area. To enable write access for this operation you must modify the decriptor settingsto give host access to this region."

edit: found the bios lock jumper, and now able to flash the bios

Actually, my situation is a bit different. The jumper was set correctly (but not to the default lock position as in the manual). I think the DOS flash utility was causing the problem, but I don't know how to fix it.

In the end, I tried Foxconn's LiveUpdate in windows and was able to flash using your "Module Method Mod". So far everything is working. Thank you so much for the help!

[DMAN999]

No Problem.
I'm glad you got it worked out.

[peach]

No Problem.
I'm glad you got it worked out.

Hello,
I have Foxconn H67S/H61SP, and my bios is A41F1026. Can I use this mod bios for my PC? I mean Module Method Mod. Thank you for your help!

[ifelsethen]

you guys probably want the newest bios (C33F1P01) SLIC'd, as it has ivy bridge CPU support. the ones being linked here are old versions.

note the rweverything report is very different when it is snapshotted againt the newest stock bios version C33F1P01. i posted the zip of rweverything report here:
http://www.bios-mods.com/forum/Thread-Re...5#pid52225