Compaq CQ60-419WM F.54A HP 2.1 SLIC

[mclatch]

I need the SLIC for a Compaq CQ60-419WM Laptop.

Bios Ver.= F.54 A
Bios Link: http://h10025.www1.hp.com/ewfrf/wc/softw...2&sw_lang=

[1234s282]

Here you go , i used HP 2.1 SLIC + Certificate Included:-

1. Copy and paste ******.XRM-MS certificate file into C-Drive.

2. After pasting this file into C-Drive, go to START - ALL PROGRAMS - ACCESSORIES - COMMAND PROMPT. Right click on Command Prompt and RUN AS ADMINISTRATOR.

3. When Command Prompt opens, type at the prompt: slmgr.vbs -ilc c:\********.xrm-ms and hit the Enter Button. Wait for the Script Host to answer you with a message that the license was installed successfully....this could take a few minutes and so be patient.

4. After receiving the message that the license was installed successfully, type at the command prompt:

slmgr.vbs -ipk *****-*****-*****-*****-***** (Replace with any OEM SLP Product Key for your installed version of Windows 7 , they are not hard to find).Be Patient and wait for the message to say that the Product Key was successfully installed. After it says successfully installed, reboot the computer.

5. When you are back at your desktop, go to START - COMPUTER - right click on Computer and choose PROPERTIES and see if it is activated with an OEM product ID.

http://dl.dropbox.com/u/747181/Compaq%20...34s282.zip

Flash at your own risk!

Please Report Back With Whether It Worked Or Not!

Please Consider A Small Donation As A "Thank You" If You Are Happy With Our Work

Regards
Admin

[mclatch]

Worked very well, thank you.

[jessey]

I just tested this with a clean install of windows 7 ultimate with multiple oem slp keys and it still wouldn't activate ( the keys were accepted fine by the cmd but after restart nothing). (is it because i entered nothing when prompted for the key during windows install) If not I don't think this works. My laptop is a cq50-215ca and it runs the exact same firmware so it can't be a problem there.

[1234s282]

I just tested this with a clean install of windows 7 ultimate with multiple oem slp keys and it still wouldn't activate ( the keys were accepted fine by the cmd but after restart nothing). (is it because i entered nothing when prompted for the key during windows install) If not I don't think this works. My laptop is a cq50-215ca and it runs the exact same firmware so it can't be a problem there.

1) Make sure you go to start , type cmd , then right click and run as administrator or the commands wont work!

2) Have you installed the certificate file? Do you receive a confirmation message after a minute or so after executing the slmgr.vbs -ilc command? The Certificate has to be installed for the procedure to work

3) Please post a screenshots from the following program

http://dl.dropbox.com/u/747181/SLIC_Dump_ToolKit.EXE

Thanks
Admin

[jessey]

1) done
2) it did confirm that it was installed without error.
3)pics below
[attachment=1397][attachment=1398]

[1234s282]

From the screenshot i can see theres a problem with the mod

Please try downloading the file again , the ROM has been updated using a different method to insert the SLIC

good luck

Admin

[jessey]

I tested this one as well and it didn't work so I tried to mod the bios myself and it worked. It probably wasn't working because of no .rw file from the computer on the original bios. (used Hp[HPQOEMSLIC-BPC]2.1.bin and ssv2)
Link:
http://www.megaupload.com/?d=LLRY8P2F
(re upload to drop box as i don't have an account with them)

[redneckrecon134]

Can someone look and see what the name of the recovery bios file is for this image? I was flashing in Windows 7 and it decided to freeze on me. I can Win + B at boot and get the bios recovery going. I see it reading thumbdrive when I boot with that combo. If I just boot without holding down those keys or a different combo I get nothing. It sits there like its expecting a certain name for the bios file and I cnt figure it out. Ive tried bios.whp and *.rom *.bin, if anyone could look at the bios and find the recovery filename they would rule.

[sonaughty]

Would someone kindly repost a link to the 2.1 slic mod for Compaq CQ60-419WM please? all of the links in this post are bad.

Thx!!