(UEFI) Dell XPS 15z L511z modded BIOS - and HOWTO

[kasar]

thanks

uh, russian! O.o

I will have a long time with the translator

I checked some of it, that usb programer is really interesting, and really small.

also have no need of external power suply and have the small size or a small usb stick!

well, since I already built my lpt programmer and I am happy with it, I think I will save the money to other stuff, starting by replace my motherboard if the bios chip is not the only damaged part ^^

but well, every modern computer have usb, that isnt the same as LPT, wich is getting very rare to find,

I used a old pentium 3 desktop machine to flash the chip image from the LPT port.


question.

do another chip with the same size in size and in Mb and same pinout work as replacement for my motherboard?

or it have to be the same one?

[TimeWalker]

There're some checks inside firmware to identify a proper chip... in fact there are even modules for it embedded in the firmware.

W25Q32FlashPartSmm.efi F8CA70B4-6A85-4616-8BDE-3EC569644AC3_1_xxx.ROM
W25Q32FlashPartDxe.efi 68BC3095-8839-4A97-8FEA-BEE06ECA7BBB_1_xxx.ROM

W25Q32BVSIG is Vendor/Device ID: 0xEF4016
Found in your L502X firmware at the offset 0xE00 which is your flash descriptor (hence the name hehe)

[kasar]

then I guess I have to get the same chip then

else I would sit like a dumb thing in front of the machine expecting it boot or do something ^^

I ask because in some cases when I asked for a electronic component on a store,they said they didnt had the specific part, but they had alternatives.

thanks for the info

[nebster]

Since we're flashing the chip directly, can't we just modify the Vendor/Device ID?

[jkbuha]

Morning all

@TheWiz - thank you for your kind offer! We've collected Eur57 so far - any spare cash is much appreciated!
@kasar - let me know when to close the pledge so I can send over the donations to your account. Have you established if it's the mobo or the chip?

[TimeWalker]

Since we're flashing the chip directly, can't we just modify the Vendor/Device ID?

Support for the chip comes inside the firmware. I believe the modules (Smm and Dxe) are coded for SPI BUS communications with PCH (Cougar Point chipset) to use this particular chip.
Same vid/pid of 0xEF4016 can be found inside both of the modules mentioned above (offset 0x2D0h).

Runnin FPT -i on the system identifies the flashrom's structure:

Code:

Platform: Intel(R) HM67 Express Chipset Reading HSFSTS register... Flash Descriptor: Valid --- Flash Devices Found --- W25Q32BV ID:0xEF4016 Size: 4096KB (32768Kb) --- Flash Image Information -- Signature: VALID Number of Flash Components: 1 Component 1 - 4096KB (32768Kb) Regions: Descriptor - Base: 0x000000, Limit: 0x000FFF ME - Base: 0x001000, Limit: 0x17FFFF BIOS - Base: 0x180000, Limit: 0x3FFFFF GbE - Not present PDR - Not present Master Region Access: CPU/BIOS - ID: 0x0000, Read: 0x0B, Write: 0x0A ME - ID: 0x0000, Read: 0x0D, Write: 0x0C GbE - ID: 0x0118, Read: 0x08, Write: 0x08 Total Accessable SPI Memory: 4096KB, Total Installed SPI Memory : 4096KB

[kasar]

@jkbuha

well, I have to determine if the chip replacement will fix the motherboard.


today I called my local electronic store, they dont have the winbond chips.

so I ordered them via the link timewalker gave to me.

http://www.ebay.com/itm/5pcs-WINBOND-W25...0668544992

the good point is that I will have 5 of them if for some reason I make another mistake.

the bad point is that it will take its time to arrive.

probably more than 1 or two weeks at least ):

well, anyway I will also go today to the local electronic store and will pick the DIP 8 socket, 100 ohm resistors, and another parallel ports to solder,

this will allow make another parallel port programmer, so I will be able to confirm the programmer is definitly ok and the chip is fried.

anyway since I didnt changed anything from the programer, I supose the chip is already broken.



@timewalker

mmm, so, if we modify the firmware and add another chip ID, it would be posible to replace the chip with another one, well, anyway i see no point doing this because the machine would be fucked on every bios update, making necesary to patch all updates with the another chip.

I also ordered the ones you said, so no issues from that way.

[TimeWalker]

Cool, so now we just wait ..

[kasar]

well, today I recived a email and it said it was being shipped, maybe those asian people are fast

oh, I though about any other posible benefict about having several bios chips.

since I will add a dip8 socket, I may able to have several flashed chips.

for example, I can allways have one with a sticker on the chip wich says "backup", so I allways carry the laptop with a working bios chip in my pocket in case I flash crap on the attached one.

that will allways have a working bios, so if I travel, I will dont have to worry about a brick.


and others I can go for testing


also, if the wires support it, I would love to add the 8 dip socket in the place the old programer port was.

replacing the chip would be as easy as remove a ram module, that would be like a dream to bios modding at the safe way and fast
I may also be able to "hot swap" the chips, but well, maybe I am going so far when I didnt even confirmed I can fix the motherboard by replacing the bios chip suposed to be fried :o

[nebster]

Yeah, they're fast at getting it into the delivery network. Problem it takes around a week or 2 for it to get anywhere =/