Bios Mods -The Best BIOS Update and Modification Source

(09-10-2015, 01:39 AM)3rav Wrote: [ -> ]Witam,
Hello,

I made an attempt to upload the modified BIOS by using the programmer CH341A, but the attempt failed:
 
1.     The programmer mistakenly recognized my chip detects it as a chip “128bit” instead of 8MB.
2.     I changed in the program to the chip COMMON 25X64.
3.     I made a backup of BIOS loaded.
4.     I programmed the chip with modified bios.
5.     Computer after step 4 did not start.
6.     I programmed the BIOS with my backup (created in step 3. - from the programmer).
7.     The computer is normally launched.

I am attaching my backup BIOS (programmer).
http://rghost.net/85QMgZ4V4

 
Please warmly about some advice.

Regards
Rafał

79CN50WW_ADV_NWL_for_HW_Program_3rav
http://rghost.net/7FpJS8rCx

Simply the Best

Hellow,

Intel network card AC7260 is already working on my laptop .



Regard
Rafał

Hello Everyone.

I would love to have a modifided Bios on my Lenovo G510.

I know that i need a CH341A Programmer. I got one from Ebay and have the Software.

So now i have the problem that i could not read my Bios Chip.

For the Test a "old" Eon EN25F80 is working.

Here is the Picture of my Bios Chip(Winbond 25Q64FVSIQ).


 I Use a "Clamp" to Read the Chip like Rafal. But the Programm give me DEVICE STATE: NOT CONNECTED.

i Use CH341A Programmer V 1.17

Maybe someone could help Thank you

Wondering if you guys can help. I've a G510 which I'd like to remove white list and unlock bios features.

I'm familiar with read/write from car ecus.

I've obtained an eeprom programmer and clip as per tutorial but when I connect clip to eeprom the led in reader goes dim and program shows programmer as disconnected as well as win 7 making the disconnected device sound. Opposite happens when I disconnect the clip from the eeprom.

I'm assuming its USB power issue. My powered USB hub doesn't make any difference.

How can I get more power to the reader so I can get my bios read, modded and flashed back.

I've spent hours googling and can't find anything on adding external power to the programmer.

TIA.

Hi mate,
I suggest to follow this Tutorial and check the alignment to Pin #1 from Chip (is present a
ball on pin 1 = foot 1) then Clip to SPI PGM :

https://www.bios-mods.com/forum/Thread-R...val?page=3

Then check if Eeprom Chip is detected !
Many times Clip doesn't work well as not good quality so You have desolder this Chip.
Let me know
Regards

(10-15-2015, 10:54 AM)BDMaster Wrote: [ -> ]Hi mate,
I suggest to follow this Tutorial and check the alignment to Pin #1 from Chip (is present a
ball on pin 1 = foot 1) then Clip to SPI PGM :

https://www.bios-mods.com/forum/Thread-R...val?page=3

Then check if Eeprom Chip is detected !
Many times Clip doesn't work well as not good quality so You have desolder this Chip.
Let me know
Regards

I know the Tutorial
As i said i could read and flash a old "Eon EN25F80" Chip with no Problem

I use a "CH341A 24 25 Series EEPROM Flash BIOS DVD USB Programmer (C1B5)" and a "SOIC8 SOP8 test clip" for the Winbond Chip. But every time i CLIP the SOIC8 Clip on the Chip the Led on the CH341A Dimms and the Programm (CH341A Programme V 1.17) switch to "DEVICE state: NO CONNECTION.

Is my software to old? Or the chip too new? Icould not finde any infos about this chip .

I am a bit frustrated.

Maybe anybody could help me in a chat seasson or so.

Thanks

Found in the Other Thread:

Quote:
a1k0n 
Junior Member


#54
10-06-2015, 07:30 PM
@ BDMaster

I was buying an CH341a Programmer and cable.
Without anything (only Programme in USB Slot) Device is Connectet.
After plug on BIOS Chip Programmer disconnects and becomes very hot.
I can't read my bios 

https://www.bios-mods.com/forum/Thread-R...val?page=6 

have the Same Problem.

Try this software use the Win7 Driver !

http://rghost.net/6rrRPtchr

Let me know
Regards

Try this software use the Win7 Driver !

http://rghost.net/6rrRPtchr

Let me know
Regards

Thank you.

But same Problem like befor.

If i Connect the Clip to the Chip the Programmer gets hot and the LED Dimms, and in the Software i got NOT CONNECTED

In the other Thread a user had the same Problem. Could you help him? Maybe i have the same Problem?!