PB EASYNOTE TK 85 REQUEST

[felipejfc]

and are you SURE this BIOS is really for your notebook?

[alierdem93]

Yeah i know it budyy

[felipejfc]

Have you tried DOS flash??
Using Flash.bat from DOS mode?
See your BIOS file has DOS and Windows folders

---

If yes and it didn't worked, try to flash this by recovery mode(Instructions included):

https://hostr.co/bpKL2whhhs75

Advanced and Power tabs unlocked as a bonus.

report.

[alierdem93]

I tried it. But its not worked for me. It say this is not compatible with your computer. (Same error )

---

I'm using DOS Flash.
I commanded : "flashit PEW71x64.fd /all"
And i tried this: "flashit KBCA230A.rom /all"
And this: "update.bat"
But "the rom file is not match this platform"

---

Now i tried recovery flashing:
1- I did combination buttons.
2- I wait fn + esc
3- I opened comp
4- This time, comp. had a blank screen
5- Then i wait continues on fn + esc buttons...
6- I waited 4 mimutes in this wise
7- But i see blank screen now :S

MY FLASH DISK 8 GB. AND FAT32 FORMATTED. ONLY IN THIS FLASHDISK "PEW71X64.fd"
Thanks

[alierdem93]

DEFAULT PACKARBELL OFFICIAL BIOS DOS FILES:
FLASHIT.EXE
KBCA230A.rom
MEInfo.exe
PEW71x64.fd
SPI.EXE
SPROM.EXE
Update.BAT

---

AND UPDATE.BAT'S CODE:

@echo off

SET BIOS_NAME=PEW71x64.fd
SET EC_NAME=KBCA230A
SET ME_VERSION=6.0.31.1208

:Retry
sprom -c:ecchk
if errorlevel 0 if not errorlevel 1 goto GPIO33Low
if errorlevel 1 if not errorlevel 2 goto FlashALL
goto Retry

@==== flash me and bios ====
:FlashALL
spi /flash -v20000 -ac -n -p6 -i %EC_NAME%.rom
cls
flashit %BIOS_NAME% /all
goto exit

:FlashBIOS
spi /flash -v20000 -ac -n -p6 -i %EC_NAME%.rom
cls
flashit %BIOS_NAME% /bios /b
goto exit

:GPIO33Low
meinfo >me.log
sprom -m:chk me.log %ME_VERSION%
if errorlevel 0 if not errorlevel 1 goto FlashBIOS
@echo on
@ECHO *****************************************************
@ECHO * Inform EC Pull GPIO 33 to Low *
@ECHO * Wait 5's System will reboot then reflash BIOS *
@ECHO *****************************************************
@echo off
sprom -e:glow
sprom -e:reboot

:exit

---

AND I USE RUFUS FOR DOS COMMANDER

---

If i try with dos flash:

Current BIOS Model name: NEW70
New BIOS Model name: PEW71
Protection: The ROM file is not match this platform
Error: The new image file is not support flash utility.

[BDMaster]

SET BIOS_NAME=PEW71x64.fd
SET EC_NAME=KBCA230A
SET ME_VERSION=6.0.31.1208

As You see KBCA230A is Embedded Controller this contains ME Region 6.0.31.1208,
then Bios is PEW71x64.fd !!!
Look here :

http://www.bios-mods.com/forum/Thread-BI...0#pid67830

I just replied before, so two choices InsydeFlash.exe without any check directly on Eeprom or Recovery Mode !
I don't know if It will give a brick (may be not), but Mobo are right ones (differents Grapic Card or Wlan, memory config, etc.)
FjFc know all, He leads You to do !
regards

[felipejfc]

In phoenixtool, the name it gave was PEW71X64.fd BDMaster...

Friend alierdem93, try the name BDMaster suggested PEW71x64.fd(Pay attention to the lower cased x), rename the file I gave you for recovery mode and try again in recovery mode with name PEW71x64.fd

report

[alierdem93]

Now, How i do it? Can u explain it? I dont understand it. Step to step please. I'm a newbie First step? second step? First startup...

[felipejfc]

try recovery with file names PEW71X64.fd and PEW71x64.fd
the instructions are included in the file I sent earlier
https://hostr.co/bpKL2whhhs75

[alierdem93]

I tried recovery bios with 8gb fat32 usb stick. computer did anythings. Usb stick's led is lighting on this section. and i waiting then i waiting ... Because comp dont be anything because looping usb sticks led is sgain lighting. thanks